350-501 Practice Test Questions Updated 373 Questions
Cisco 350-501 Dumps - Secret To Pass in First Attempt
NEW QUESTION 45
ASN 65001 is peering with ASN 65002 to exchange IPv6 BGP routes. All routes that originate in ASN 65001 have a standard community value of 65001:100, and ASN 65002 is allowed to advertise only
2001:db8:aaaa::/48. An engineer needs to update the ASN 65001 route-filtering configuration to meet these conditions:
* Looped routes into ASN 65001 and routes that have traversed 10 or more ASNs must be denied.
* Routes accepted into ASN 65001 must be assigned a community value of 65001:200.
Which configuration must be engineer apply to the ASN 65001 border router?
- A.
- B.
- C.
- D.
Answer: D
Explanation:
Section: Networking
NEW QUESTION 46
Refer to the exhibit.
While troubleshooting the network, a network operator with an employee id: 3812:12:993 is trying to ping XR1. Which result should the operator expect when trying to ping to an XR1 local address?
- A. All ICMP traffic responds successfully.
- B. ICMP traffic works at a policed rate of 19 bytes per second every 100 ms
- C. All ICMP traffic is dropped.
- D. ICMP traffic works at a policed rate of 19 packets every 100 ms.
Answer: A
NEW QUESTION 47
Refer to the exhibit:
After implementing a new design for the network, a technician reviews the pictured CLI output as part of the MOP.
Which two statements describe what the technician can ascertain from the ImpNull output? (Choose two.)
- A. Label 3 is in use for the prefix displayed and will be part of the MPLS label stack for packets destined for 192.168.10.10
- B. Ultimate Hop Popping is in use for the prefix displayed.
- C. Label 0 is used for the prefix displayed but will not be part of the MPLS label stack for packets destined for 192 168.10.10.
- D. Penultimate Hop Popping is in use for the prefix displayed
- E. Label 0 is used for the prefix displayed and will be part of the MPLS label stack for packets destined for 192.168.10.10
Answer: A,D
NEW QUESTION 48
Which additional feature does MPLS DiffServ tunneling support?
- A. interaction between MPLS and IGP
- B. PHB layer management
- C. using GRE tunnels to hide markings
- D. matching EXP and DSCP values
Answer: B
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/mp_te_diffserv/configuration/15-mt/mp-te-diffserv-15-mt-bo
NEW QUESTION 49
Which descriptions of Netflow is correct? (Choose three.)
- A. Netflow accounts for both transit traffic and traffic destined for the router.
- B. Netflow answers questions regarding IP traffiC. who, what, where, when, and how
- C. By default,Netflow records bidirectional IP traffic flow.
- D. Netflow returns the subinterface information in the flow records.
Answer: A,B,D
NEW QUESTION 50
Refer to the exhibit.
A network engineer is configuring customer edge routers to finalize a L2VPN over MPLS deployment Assume that the AToM L2VPN service that connects the two CEs is configured correctly on the service provider network Which action causes the solution to fail?
- A. OSPF does not work with L2VPN services
- B. A loopback with a /32 IP address has not been used
- C. The x connect statement has not been defined
- D. The routing protocol network types are not compatible
Answer: C
NEW QUESTION 51
Refer to the exhibit.
Refer to the exhibit. A network engineer is implementing multicast Source-A to send a multicast stream for Receiver-A, and multicast Source-B to send a multicast stream for Receiver-B. Router RC forwards the IGMP host a report and leaves messages to IP address 192.168.10.1. How must the multicast features be implemented to prevent RB from receiving multicast flooding from Source-A?
- A. Change the helper-address value to 192.168.10.2 on RC.
- B. Configure PIM-SSM on RB and RC interface Ge 0/0.
- C. Enable ip pim passive on RB interface Ge0/0.
- D. Enable ip pim neighbor-filter on RC interface Ge0/0.
Answer: C
NEW QUESTION 52
Refer to the exhibit. Routers P4 and P5 receive the 0.0.0.0/0 route from the ISP via eBGP peering. P4 is the primary Internet gateway router, and P5 is its backup. P5 is already advertising a default route into the OSPF domain. Which configuration must be applied to P4 so that it advertises a default route into OSPF and becomes the primary Internet gateway for the network?
- A. configure terminal
router ospfv3 100
address-family ipv4 unicast
default-information originate metric 40 metric-type 2
end - B. configure terminal
router ospfv3 100
address-family ipv4 unicast
redistribute bgp 65500 metric 40 metric-type 1
end - C. configure terminal
router ospfv3 100
address-family ipv4 unicast
default-information originate always metric 40 metric-type 1
end - D. configure terminal
router ospfv3 100
address-family ipv4 unicast
default-information originate metric 40 metric-type 1
end
Answer: A
NEW QUESTION 53
Refer to the exhibit.
Refer to the exhibit. ISP ASN 65100 provides Internet services to router CE-1 and receives customer prefix 198.18.18.0/24 via eBGP. An administrator for the ISP is now provisioning RTBH services to provide on-demand data-plane security for the customer's IP space. Which route-map configuration must the administrator apply to router RTBH-1 to complete the implementation of RTBH services to CE-1?
- A. route-map RTBH-CUSTOMER-IN permit 10
description AS65001
match ip address prefix-list AS65001-PREFIXES
match community 99
set local-preference 200
set community no-export additive
set ip next-hop 192.168.255.255
route-map RTBH-CUSTOMER-IN deny 65535
description DEFAULT DENY - B. route-map RTBH-CUSTOMER-IN permit 10
description AS65001
match ip address prefix-list AS65001-PREFIXES
match community 99
set local-preference 200
set community no-advertise additive
set ip next-hop 192.168.255.255
route-map RTBH-CUSTOMER-IN deny 65535
description DEFAULT DENY - C. route-map RTBH-CUSTOMER-IN permit 10
description AS65001
match ip address prefix-list AS65001-PREFIXES
match community 99
set local-preference 200
set community local-as additive
set ip next-hop 192.168.255.255
route-map RTBH-CUSTOMER-IN deny 65535
description DEFAULT DENY - D. route-map RTBH-CUSTOMER-IN permit 10
description AS65001
match ip address prefixlist AS65001-PREFIXES
match community 99
set local-preference 200
set community no-advertise additive
set ip next-hop local-address
route-map RTBH-CUSTOMER-IN deny 65535
description DEFAULT DENY
Answer: A
NEW QUESTION 54
Refer to the exhibit. What does this value mean when it is received in XML?
- A. It means a data field is blank
- B. It shows the ending of the script
- C. It indicates a value assigned by a network administrator to tag a route
- D. It indicates a break in a sequence
Answer: A
Explanation:
When no data exist, you can represent a level of XML hierarchy in one of two ways:
using opening and closing tags: <tag></tag>
using shorthand notation: <tag/>
NEW QUESTION 55
Refer to the exhibit.
Refer to the exhibit. A network operator is attempting to configure an IS-IS adjacency between two routers, but the adjacency cannot be established. To troubleshoot the problem, the operator collects this debugging output. Which interface are misconfigured on these routers?
- A. Option C
- B. Option B
- C. Option D
- D. Option A
Answer: B
NEW QUESTION 56
Refer to the exhibit. An engineer is preparing to implement link aggregation configuration.
Which statement al about this configuration is true?
- A. The switch port actively sends packets to negotiate an EtherChannel using PAgP
- B. The switch port accepts LACP and PAgP packets from a connected peer and negotiate an EtherChannel using the common EtherChannel mode.
- C. The switch port negotiates an EtherChannel if it receives LACP packets from a connected peer
- D. The switch port passively negotiates an EtherChannel if it receives PAgP packets from a connected peer
Answer: A
Explanation:
https://www.cisco.com/en/US/docs/switches/metro/me3600x_3800x/trash/swethchl.html
NEW QUESTION 57
Refer to the exhibit. The network team must implement MPLS LDP session protection with two requirements:
- Session protection is provided for core loopback IP addresses only.
- The LDP session must remain operational for one hour when the WAN
link on PE-XR1 fails.
Which configuration must the team implement on PE-XR1?
- A. Option C
- B. Option B
- C. Option D
- D. Option A
Answer: C
NEW QUESTION 58
Refer to me exhibit. An engineer started lo configure a router for OSPF.
Which configuration must me engineer perform on me router without changing any interface configuration so that the router establishes an OSPF neighbor relationship with its peer?
- A. Option C
- B. Option A
- C. Option D
- D. Option B
Answer: B
NEW QUESTION 59
Refer to the exhibit.
A network administrator is implementing IGMP to enable multicast feed transmission to the receiver. Which configuration must the administrator deploy on GW1 to permit IGMP Joins only to the assigned (S, G) feed?
A)
B)
C)
D)
- A. Option C
- B. Option B
- C. Option D
- D. Option A
Answer: B
Explanation:
NEW QUESTION 60
Refer to the exhibit.
An engineer is trying to implement BGP configuration on a router Which configuration error prevents the ASBR from establishing a BGP neighborship to a directly connected BGP speaker?
- A. The TCP session parameters are not specified.
- B. The VPNv4 address family interferes with the 8GP IPv4 address family negotiations.
- C. The routing policy is absent for this Cisco IOS XR eBGP instance.
- D. The IPv4 address family configuration under neighbor configuration-mode must be removed.
Answer: C
Explanation:
https://www.cisco.com/c/en/us/td/docs/routers/xr12000/software/xr12k_r41/routing/configuration/guide/routing_cg41xr12k_chapter1.html bgp router-id comes under TCP session parameters
NEW QUESTION 61
Refer to the exhibit.
A network engineer is configuring customer edge routers to finalize a L2VPN over MPLS deployment Assume that the AToM L2VPN service that connects the two CEs is configured correctly on the service provider network Which action causes the solution to fail?
- A. OSPF does not work with L2VPN services
- B. A loopback with a /32 IP address has not been used
- C. The x connect statement has not been defined
- D. The routing protocol network types are not compatible
Answer: C
NEW QUESTION 62
Refer to the exhibit.
While troubleshooting a connectivity issue on router R2, a network engineer with an employee id:3876.13.497 notices that although it detects three OSPF links from R1, the OSPF prefixes are missing from the routing table. What is the reason for the problem?
- A. The R2 Serial 1/0 interface is configured with an IP address, but the R1 Serial R1 Serial 1/0 interface in unnumbered.
- B. The serial interfaces have different MTUs
- C. The subnet masks on the serial interfaces are mismatched.
- D. Both loopback interfaces on R1 are configured as stub
Answer: A
NEW QUESTION 63
Refer to the exhibit.
An engineer began to configure LDP between R1 and R2, but R1 and R2 cannot yet establish an LDP TCP connection. Which additional task must be completed to finish the implementation?
- A. Configure the mpls Idp neighbor 10.0.12.1 password command on R1
- B. Configure the no mpls Idp password option 1 command on R1
- C. Configure the no mpls Idp password option 1 command on R2
- D. Configure the mpls Idp neighbor 172.16.0.1 password command on R1
Answer: D
NEW QUESTION 64
Refer to the exhibit:
This output is included at the end of an output that was provided by a device using NETCONF.
What does the code show?
- A. It shows the hostname of the device as rpc-reply
- B. It shows NETCONF uses remote procedure calls.
- C. It shows that the running configuration is blank
- D. It shows that the full configuration is being modeled by VANG
Answer: A
NEW QUESTION 65
Refer to the exhibit:
R1 is connected to two service providers and is under a DDoS attack Which statement about this design is true if uRPF in strict mode is configured on both interfaces'?
- A. R1 drops destination addresses that are routed to a null interface on the router
- B. R1 accepts source addresses on interface gigabitethernet0/1 that are private addresses
- C. R1 drops all traffic that ingresses either interface that has a FIB entry that exits a different interface
- D. R1 permits asymmetric routing as long as the AS-RATH attribute entry matches the connected AS
Answer: C
NEW QUESTION 66
Refer to the exhibit:
A network administrator wants to enhance the security for SNMP for this configuration.
Which action can the network administrator implement?
- A. Re-configure to use SNMPv2 with MD5 authentication
- B. Add a community string to the existing entry
- C. Re-configure to use SNMPv3.
- D. Maintain the configuration but switch to an encrypted password for device access through SSH
Answer: C
NEW QUESTION 67
Refer to the exhibit:
Which statement describes this configuration?
- A. Router 1 has a temporary data store where a copy of the running configuration can be manipulated and verified before committing the configuration
- B. Router 1 has its running configuration locked so changes can be made only when the administrator issues a kill session
- C. Router 1 can be remotely managed by the CLI using Telnet
- D. Router 1 has a new data store to collect SNMP information, but configuration must still be done at the CLI only
Answer: A
NEW QUESTION 68
ASN 65001 is peering with ASN 65002 to exchange IPv6 BGP routes. All routes that originate in ASN 65001 have a standard community value of 65001:100, and ASN 65002 is allowed to advertise only 2001
:db8:aaaa::/48. An engineer needs to update the ASN 65001 route-filtering configuration to meet these conditions:
* Looped routes into ASN 65001 and routes that have traversed 10 or more ASNs must be denied.
* Routes accepted into ASN 65001 must be assigned a community value of 65001:200.
Which configuration must the engineer apply to the ASN 65001 border router?
A)
B)
C)
D)
- A. Option C
- B. Option A
- C. Option D
- D. Option B
- E. Option E
Answer: B
NEW QUESTION 69
......
Apart from courses, applicants can refer to various books. These are two tested and credible guides to consider using:
- How I Passed Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR 350-501) Exam: Successfully Proven Tips by Rocismo Liolentz Publications
This book is available on Amazon in Kindle format. The publisher uses verified tips to help the candidates pass the Cisco 350-501 certification exam from the first attempt. The material contains 76 pages of advice and hints on how to successfully ace this test, including a time-management plan, exam design, registration procedure, pitfalls, and much more. Moreover, the author mentions that they collected feedback from thousands of past successful candidates on how they managed to obtain the passing score. Therefore, they used the most useful techniques and included them in this book which can be seen as a valuable guide to become a certified Cisco Specialist on Service Provider Core.
- CCNP Service Provider - (SPCOR 350-501) by Saransh Paliwal
This book is available in Kindle format on the Amazon website and it has been prepared by Saransh Paliwal. It observes the Cisco 350-501 exam structure and helps the candidates consolidate their knowledge for each test section such as core architecture, services, networking, automation, security, as well as network assurance. Apart from following the exam blueprint, this edition contains a detailed explanation of all topics related to Cisco Core Technologies. Therefore, this guide becomes a valuable tool that the examinees can use to check their preparedness level and clarify any questions they might have in the process of getting ready for 350-501 exam.
Cisco 350-501 Exam Dumps [2023] Practice Valid Exam Dumps Question: https://officialdumps.realvalidexam.com/350-501-real-exam-dumps.html
