Latest [Jul 23, 2022] NACE NACE-CIP1-001 Real Exam Dumps PDF
NACE-CIP1-001 Practice Test Questions Updated 100 Questions
NEW QUESTION 24
Dew point is the temperature at which
- A. water freezes.
- B. humidity decreases
- C. the air is saturated.
- D. condensation occurs.
Answer: D
NEW QUESTION 25
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use
- A. a detailed checklist and document the lack of a standard.
- B. their best judgment based on similar projects and specifications.
- C. a recognized industry standard like SSPC-PA 2 that is broadly accepted
- D. NACE 2/SSPC SP10
Answer: C
NEW QUESTION 26
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Review the NACE Attestation prior to making a decision
- B. Accept the assignment without hesitation
- C. Meet with the prospective employer to determine the scope of your role
- D. Advise the prospective employer that you cannot accept the position
Answer: C
NEW QUESTION 27
According to SSPC PA 2 a Spot Measurement is:
- A. A single gauge reading
- B. The overall average of all readings
- C. The average of gauge readings taken in a 4cm (1.5 inch) circle
- D. The average of all spot measurements in a given area
Answer: C
NEW QUESTION 28
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Keep doing the checks and consult the Owner's representative for direction
- B. Skip the checks and just record the same readings as you have been getting
- C. Keep doing the checks regardless
- D. Skip the checks as you are. confident the blast pressure is OK
Answer: A
NEW QUESTION 29
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 3
- B. Level 1
- C. Level 4
- D. Level 2
Answer: A
NEW QUESTION 30
NACE SP 0178 is a standard for:
- A. Tanks and Vessels to be Externally Coated
- B. Tanks and Vessels to, be Lined for Immersion Service
- C. Structural steel to be coated for Atmospheric Service
- D. Stainless steel pipe to be Externally Coated
Answer: B
NEW QUESTION 31
On a blast-cleaned surface, Ian ultraviolet light is generally used to detect
- A. soluble chemical salts
- B. grease and oil
- C. sulfates
- D. inhibitor residues
Answer: B
NEW QUESTION 32
Excessive working of the surface with a power grinder can be detrimental because excessive burnishing
- A. damages structural elements thereby speeding up the corrosion process.
- B. scratches the surface too deeply resulting in uneven coating application
- C. develops a polished surface, which is a poor anchor profile for most coatings
- D. develops a good anchor profile resulting in uneven coating application.
Answer: C
NEW QUESTION 33
Stripe coats are generally applied to:
- A. Welds
- B. Complex geometric shapes
- C. Edges and corners
- D. a), b), and c)
Answer: D
NEW QUESTION 34
Due to a previous premature coating failure the owner has required the original coating applicator to return to remove and replace 10,000 square feet of a failed three coat system at the applicator's cost. Due to the financial implications of another failure, the owner has offered you the job as the NACE CIP Level 1 Coating Inspector and explained that he expects you to be his "insurance policy" for this job. You have never been involved in a warranty job before and are unfamiliar with the coating system.
Your preferred FIRST course of action is to:
- A. Meet with the owner and explain your limitations and concerns prior accepting the assignment
- B. Review the Product Data Sheets and meet with the Coating Applicator 'prior to the pre-job meeting
- C. Review the Product Data Sheets, and conduct a walk thru of the job site prior to the pre-job Conference
- D. Purchase Professional Liability Insurance prior to job commencement
Answer: C
NEW QUESTION 35
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Achieve consensus through negotiation
- B. Never change his/her mind
- C. Call the supervisor
- D. Go with the majority opinion
Answer: C
NEW QUESTION 36
Owners hire NACE Inspectors' with the expectation that:
- A. The Inspector will make a meaningful technical contribution to the job
- B. The Inspector will improve job flow and schedule
- C. a) and c)
- D. The inspection cost will be offset by an improvement in service life
Answer: C
NEW QUESTION 37
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Presence of weld spatter may produce a false positive
- B. Ultra-Violet light may contaminant the surface
- C. Synthetic oil or grease may not be identified
- D. Chloride salt may produce a false positive
Answer: C
NEW QUESTION 38
Inspection documentation is important because:
- A. It is the only deliverable item provided by the inspector
- B. a) only
- C. Owners use the documentation for a variety of purposes
- D. a) & b)
Answer: C
NEW QUESTION 39
Checking is
- A. surface breaks in the film that often result from grease or oil contamination and revel the substrate.
- B. a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.
- C. an exposed area of the substrate or previous coat material, caused by poor application technique.
- D. a fine crack in the surface of a coating that rarely reaches the substrate
Answer: D
NEW QUESTION 40
To be of value the Inspector's documentation must be:
- A. Always typewritten
- B. Always handwritten
- C. Timely, accurate and concise
- D. Submitted before the end of the job
Answer: C
NEW QUESTION 41
......
Do you know about the need for the NACE CIP1-001 exam?
There are different kinds of certifications that can help candidates to achieve a good career. The NACE CIP1-001 exam is one of them. It allows the candidates to get a certification as a certified coatings inspector. There are different types of NACE CIP1-001 exams available. You can choose any of them. You should not waste your time by choosing any wrong exam. We are giving you all the information about the NACE CIP1-001 exam. Choose a suitable exam for you. A credit card can be used to purchase any product or service. You can use it to pay for the NACE CIP1-001 exam dumps. A prospective employer can easily find a suitable candidate through these materials. Our products are very helpful in the preparation for this exam. It is the best material that you can use to pass this exam easily. Permitted to transport is the most important issue for any business. Abrasive is a type of powder used in various industries. It is also called abrasive dust. The purpose of using this powder is to remove the unwanted layers from any surface. It is used in many types of industries such as steel, power, mining, and construction. In this process, abrasive can be harmful to people. There are different types of abrasive available. They include fine, coarse, superfine, and ultrafine.
NACE NACE-CIP1-001 Dumps - Secret To Pass in First Attempt: https://officialdumps.realvalidexam.com/NACE-CIP1-001-real-exam-dumps.html
